Home 
Home Search search Menu menu Not logged in - Login | Register
> subwoofer

Profile Topics Posts
Posts by subwoofer
617 postsShowing posts 201-240 of 617

Suspension > Fitting rear Superpro bushes (27 replies - 50534 views)

And on the subject of crush tubes. They must be inserted AFTER the cotton reel is in place. -- Joachim ...   09-21-2013 01:24 pm

Suspension > Fitting rear Superpro bushes (27 replies - 50534 views)

First of all, the outer shell of the old bushing must be removed, but I guess you already did that. What I did to install ...   09-21-2013 12:29 pm

Projects > The Red Fox (15 replies - 27003 views)

Later spec European engine then, like mine. 9.5:1 roughly, a lot better than the Federal 8.4:1. ...   09-20-2013 09:08 pm

Projects > The Red Fox (15 replies - 27003 views)

SJ Sportscars sell 11:1 pistons for the 2.0, you could email them to see if they can compare pictures. You may be in luck. -- Joachim ...   09-20-2013 06:59 pm

Wheels > Wheel centre (pilot) bore? (4 replies - 12406 views)

Measured the hubs tonight, as far as I can tell the required centre bore is 51.1mm (which I have seen in a list of spacers). I ...   09-17-2013 07:36 pm

Wheels > Wheel centre (pilot) bore? (4 replies - 12406 views)

Does anyone know the correct centre bore? The stock wheels use the cap for centering, does anyone know the nominal measurements? -- Joachim ...   09-16-2013 08:57 am

Wheels > Stock wheel offset (19 replies - 36285 views)

Dakota123 wrote: Oh, and what is a DCA40s ECU -- I'm not familiar with it? I am guessing it is a typo, and that he meant DTA ...   09-11-2013 07:00 pm

Wheels > Stock wheel offset (19 replies - 36285 views)

gmgiltd wrote: Did you go for the Hispec kit? Front setup is excellent but the rears need longer studs and 6mm spacers to clear caliper to ...   09-11-2013 06:58 pm

Ignition > Fuel Injection KIt for 907 (109 replies - 204683 views)

Reviving this old thread for some possibly great news! I have at regular intervals been nagging the people at EightStack (http://eightstack.com/) for a DCOE/DHLA sidedraft version ...   09-11-2013 07:26 am

Wheels > Stock wheel offset (19 replies - 36285 views)

The brakes are sitting in boxes in my garage just waiting for me to get my finger out... :-) You are going fuel injected? I doubt ...   09-11-2013 07:19 am

Wheels > Stock wheel offset (19 replies - 36285 views)

Which "corner" of the wheel is problematic? If your wheels are ET15 and any of the inner corners rub, reducing ET will help. But a ...   09-11-2013 05:48 am

Wheels > Stock wheel offset (19 replies - 36285 views)

Thanks, it did! It looks like I'll be ordering ET5, then. Since 6x15 ET15 does not hit anything, neither will 7x15 ET5 - unless of ...   09-04-2013 06:15 am

Wheels > Stock wheel offset (19 replies - 36285 views)

What offset does your 6x15s have? It should be stamped on the rim. -- Joachim ...   09-02-2013 06:06 am

Wheels > Stock wheel offset (19 replies - 36285 views)

:-) I have been playing a bit with this one: http://www.rimsntires.com/specs.jsp At the moment Ms Jensen is shod with 185/70R13s on stock rims. The calculator seems to suggest ...   09-01-2013 09:18 am

Wheels > Stock wheel offset (19 replies - 36285 views)

The markings on the stock rims seems to suggest that the ET of the stock wheels is roughly 19mm, but measuring (with tyre mounted) seems ...   08-31-2013 06:33 pm

Projects > 10628 Refresh (63 replies - 98393 views)

Since you are planning on running MAF (at some point), you really should get an MS3 - the code being worked on now is MS3 ...   08-27-2013 05:38 pm

Projects > 10628 Refresh (63 replies - 98393 views)

Dakota123 wrote: Megasquirt (using some fairly well-worn Dellortos as throttle bodies). Will you be using the "TB"s dry and have a visible fuel rail, or ...   08-27-2013 06:53 am

Projects > 18711 "Miss Jensen" (129 replies - 246003 views)

Not too much driving this summer, been way too busy on other arenas. But, I do get to fix the occasional something. The fire extinguisher ...   08-24-2013 07:06 pm

Electrical & Instruments > Starter running via the Ghost of Lucas? (23 replies - 33131 views)

Just a small heads up: I think the Flamethrower is a 12V coil, so you shouldn't have a ballast resistor in the circuit. I run ...   08-18-2013 11:26 am

Fuel Stuff > Fuel type (3 replies - 10350 views)

The stock JH 907 has next to no compression (8.5:1) and still fast combustion chambers, so octane rating is not likely to be an issue. ...   07-16-2013 09:08 am

Electrical & Instruments > Oil Pressure/Temp T Fitting (5 replies - 10161 views)

1/8"NPT and M10x1.0 are close enough in pitch and diameter that they can be interchanged, but watch for leaks. NPT threads are conical, M threads ...   06-20-2013 05:14 am

Projects > 18711 "Miss Jensen" (129 replies - 246003 views)

Seconds from disaster! One of the fittings on the oil cooler sandwich plate had loosened itself. It held up when I pulled out of the garage, ...   05-05-2013 08:50 pm

Projects > 18711 "Miss Jensen" (129 replies - 246003 views)

It has been quiet from me for quite a while, Megasquirting the family barge has been the priority for a while. The new loom is ...   04-26-2013 07:07 pm

Ignition > Gear reduction starter (8 replies - 16538 views)

My starter is on its last knees... It gave up completely two years ago, then I tore it apart, cleaned it out and bolted it ...   04-19-2013 08:56 am

Ignition > Gear reduction starter (8 replies - 16538 views)

Here is one that will fit (bottom of page): http://www.britishstarters.com/Lotus.html And another one: http://classicgarage.com/eselecgerest.html -- Joachim ...   04-18-2013 05:56 am

Cooling > Heater box vacuum valve purpose (4 replies - 11855 views)

VW used one in the Vanagon for the front heater, shouldn't cost more than 20-25 bucks (unless the US parts prices are insane). -- Joachim ...   04-17-2013 04:21 pm

Body & interior stuff > Custom Dashboard Project (16 replies - 25060 views)

Here is how you link the photos to show in the post (hit "Quote" to see the markup: While viewing the picture you want to post ...   04-07-2013 06:41 pm

Body & interior stuff > Custom Dashboard Project (16 replies - 25060 views)

There is a way around the upload size problem... Upload the pictures to (say) Photobucket and link to them with IMG tags, This is what ...   04-02-2013 07:52 pm

Wheels > Correct offset or backspacing for 15x7 wheel? (2 replies - 9657 views)

Did you ever get to the bottom of this, Steve? I want to order myself a set of 15x7" Revolution 5-spokes, but I have to ...   03-11-2013 08:14 pm

Engine & Transmission > valve cover gasket replacement - tips for success (4 replies - 11644 views)

With the rubber gaskets from the club store I have had no problems at all. Simply place them over the cam carrier, thread in the ...   03-05-2013 11:07 am

Engine & Transmission > Living the dream: JH W58 5spd (40 replies - 63925 views)

Jensen Healey wrote: Sander, these cars are not museum pieces, they are meant to be driven, modified, rebuilt, raced, and ultimately, scrapped. Whoever has the most fun ...   03-03-2013 09:02 pm

Cooling > Alternate radiator sources (3 replies - 12044 views)

This was sorted years ago, had a local radiator shop fit the largest core from Nissens that would fit the tanks. -- Joachim ...   03-03-2013 08:49 pm

Engine & Transmission > Idle (4 replies - 9563 views)

Ms Jensen had the worst worn carbs in history, so vacuum leaks were abundant. Give the throttle axles a wiggle, there should be no radial ...   03-02-2013 12:47 pm

Brakes > Metric? (8 replies - 14432 views)

And I thought freight rates from the UK to Norway were bad... I'll grab the chance while the Pound is weak to get myself a set ...   02-25-2013 09:17 pm

Brakes > Metric? (8 replies - 14432 views)

have you googled the part number? I got a new master cylinder a few years back, was listed for a Land Rover IIRC. Was about £50. -- Joachim ...   02-25-2013 07:19 pm

Engine & Transmission > 40/45 DelOrtto's (6 replies - 11633 views)

Back in the seventies wideband O2 sensors and data logging systems were not readily available. No one had those analytics capabilities back then, so no ...   02-25-2013 07:16 pm

Electrical & Instruments > Resistor wire (4 replies - 9726 views)

Mitch Ware wrote: How many volts should be coming down the resistor wire from the tach to the coil? I've got about 2.5, that seems like ...   10-17-2012 04:39 pm

Electrical & Instruments > Resistor wire (4 replies - 9726 views)

chiromaster wrote: I just pulled off the resistor wire off the + side of the coil and got 11.60v Opening the circuit like that will always get ...   10-17-2012 04:37 pm

Engine & Transmission > Foamy greenish oil (11 replies - 17191 views)

Do not run it for long before checking the oil again, but if you didn't disconnect and/or empty the oil cooler and lines, you should ...   09-15-2012 06:00 pm

Projects > 16173 will be entering project status... (162 replies - 258184 views)

Are you sure some DPO hasn't jumped the coil+ wire from another circuit? The tach will only work if it is connected in series with ...   09-14-2012 08:57 pm


 Current time is 02:41 pm
 First Page Previous Page  1  2  3  4  5  6  7  8  9  10  11  ...  Next Page Last Page


UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems