Home 
Home Search search Menu menu Not logged in - Login | Register
> subwoofer

Profile Topics Posts
Posts by subwoofer
617 postsShowing posts 161-200 of 617

Projects > 18711 "Miss Jensen" (129 replies - 245987 views)

Swapped starters today. My patience with the old Lucas starter was finally worn through when I, due to a slight brain fart, managed to get ...   09-07-2014 11:21 am

Wheels > Tire Size (25 replies - 67613 views)

I run 205/50R15s on 7x15" wheels. ET5 is just on the limit, I think I would buy ET10 wheels if I were to buy again. As ...   09-03-2014 05:18 am

Ignition > No start... (4 replies - 9880 views)

If the starter gave in - but he did say it sounded normal on cranking - consider getting a brand new geared starter. I have ...   08-31-2014 05:44 pm

Ignition > No start... (4 replies - 9880 views)

Crikey! If the crank is turning and the cams don't, it WILL be expensive. Degree of expensiveness depends on engine speed when the cams stopped ...   08-30-2014 06:44 pm

Ignition > Having trouble re-installing the distrubtor (3 replies - 8777 views)

The whole thing is spring loaded! You have to seat it, then hold it in place with one hand while tightening with the other. ...   08-26-2014 07:11 pm

Carburetors > Webers or ? (23 replies - 46371 views)

Mods: This thread should be moved to the appropriate forum? Paul Koehler wrote: Beg,borrow, buy or steal Des Hammond's book on Dellorto's & Weber carbs; read it  ...   08-20-2014 06:59 am

Engine & Transmission > Stainless steel exhaust front box removal (3 replies - 8274 views)

On Ms Jensen there is a smallish resonator around where I would have expected a front muffler to be. As I understand it, in terms ...   08-15-2014 09:18 am

Projects > 18711 "Miss Jensen" (129 replies - 245987 views)

No lug bolts in the kit I received, will have to get some. My local parts pusher has 7/16"x43mm bolts from Grayston in stock, will ...   06-28-2014 06:54 pm

Projects > 18711 "Miss Jensen" (129 replies - 245987 views)

Will have to check package contents, they may be in there... Good thing I just got myself a 20 ton hydraulic press, makes installing stuff ...   06-28-2014 02:14 pm

Projects > 18711 "Miss Jensen" (129 replies - 245987 views)

Thanks for the tip, Gordon! What length bolts did you get? -- Joachim ...   06-28-2014 11:10 am

Projects > 18711 "Miss Jensen" (129 replies - 245987 views)

As promised: http://i440.photobucket.com/albums/qq129/subwooferbone/83A67B9E-2B73-4429-A1BD-DF711968BBF6_zpsjcecimw4.jpg Got the front brakes all buttoned up last night, had a quick road test before bedtime. I AM IMPRESSED! The difference in stopping power ...   06-28-2014 08:01 am

Projects > 18711 "Miss Jensen" (129 replies - 245987 views)

Finally got a few hours to work on the car - home alone for a few days. Yiiihaw! http://i440.photobucket.com/albums/qq129/subwooferbone/03871DEA-5AB5-49D3-9FBB-ECF603E301B3_zps3dixha8r.jpg Right front as it used to be http://i440.photobucket.com/albums/qq129/subwooferbone/F7EEAC39-9411-4561-9B5E-AF2883474D8F_zpsnrhfydzm.jpg Dust shield ...   06-26-2014 08:25 pm

Projects > 18711 "Miss Jensen" (129 replies - 245987 views)

For those who wonder, here is a link to the Norwegian MoT inspection guidelines: http://www.vegvesen.no/_attachment/563937/binary/910948?fast_title=Revidert+kontrollveiledning+gjeldende+fra+31+12+2013.pdf Not all of it is relevant to passenger cars, thankfully... ...   06-18-2014 04:58 pm

Projects > 18711 "Miss Jensen" (129 replies - 245987 views)

For those curious as to why I didn't swap the brakes over before the MoT; There was a risk that I would have to put ...   06-18-2014 10:16 am

Projects > 18711 "Miss Jensen" (129 replies - 245987 views)

MoT today, no points on her! It's time for a brake refreshment, I now have 2 years to get the paperwork in order before the ...   06-17-2014 10:30 am

Engine & Transmission > CNC porting the 907 head (3 replies - 8362 views)

You are aware that Lotusbits already have CNC ported heads, and judging by the dyno plots they are not useless. 280+ BHP from a 2.5l ...   06-13-2014 08:19 am

Brakes > Brake upgrade? (27 replies - 51518 views)

The full kit (front & back) is £1200-ish shipped as a kit. I am hoping to install my new brakes sometime in June, just have ...   05-22-2014 10:18 am

Ignition > HELP! Serious running issues! (7 replies - 15091 views)

Does the fuel flow from the carb while the fuel pump is running, or just while cranking? I am sort of guessing you have a sunk ...   05-05-2014 04:52 pm

Ignition > HELP! Serious running issues! (7 replies - 15091 views)

answerman wrote: Fuel is just pouring out of the front carb. Your answer is right there, it is drowning in fuel. The question is why, and it ...   05-05-2014 07:19 am

Projects > 19744 Running (14 replies - 24129 views)

I believe 9V is the correct output voltage for the stabilizer. -- Joachim ...   04-07-2014 05:35 am

Ignition > Electronic Ignition (13 replies - 23341 views)

Use a Pertronix-II instead. Works with my tach (to the extent said tach can be said to be working, it is old and knackered), installs ...   03-27-2014 06:10 am

Carburetors > Weber DCOE 37mm choke / Carb Coughing-Sneezing (9 replies - 26130 views)

Feeling sorry for you about the header flange, a real pain to redo (if we are talking head to header flange). I am guessing that you ...   02-25-2014 05:19 am

Engine & Transmission > 318 Chrysler main bearing (6 replies - 11781 views)

If I am not much mistaken, the block has to be align bored after 10-doweling the bearing frame, right? In that case it makes sense ...   02-04-2014 07:55 am

Engine & Transmission > cams, valve timing and ignition timing (106 replies - 145222 views)

MOP is also known as LCA, Lobe Centre Angle. For 260 degree cams and 110/110 timing, you will have the following timing: Ex: Open 60 degrees ...   01-31-2014 08:16 am

Projects > 16173 will be entering project status... (162 replies - 258162 views)

Pictures, or it didn't happen! :-) PM me if you can't figure out how to attach pictures. -- Joachim ...   01-14-2014 06:38 am

Engine & Transmission > Getting the rocker covers oil tight (9 replies - 13964 views)

The rubber gaskets are supposed to be installed dry AFAIK. I have had no leaks and no extrusion when (re)fitting mine. -- Joachim ...   12-23-2013 12:55 pm

Carburetors > Weber DCOE 37mm choke / Carb Coughing-Sneezing (9 replies - 26130 views)

Float height is really an irrelevant measure as it varies too much from float to float, fuel level is what you want to measure. Carb ...   11-28-2013 06:47 am

Engine & Transmission > 907 engine in work stand (6 replies - 10735 views)

Try to mount it so the mount points are as far from eachother as possible and you should be fine. That reduces the pull/push on ...   11-26-2013 08:08 pm

Carburetors > Dellorto DHLA 45 Has No Fuel Main Jets (6 replies - 12097 views)

If the engine ran at part throttle or above the jets must be there. But unless you look closely enough the parting line is hard ...   11-25-2013 05:43 am

Carburetors > Morgan Carbtune (33 replies - 53008 views)

Low compression and smoke would suggest blow-by, i.e. that the piston rings and/or the liners are worn out. See if you have oil mist coming ...   11-20-2013 08:17 am

Projects > 18711 "Miss Jensen" (129 replies - 245987 views)

Thanks! Had to have her out for some photos today. http://i440.photobucket.com/albums/qq129/subwooferbone/null_zps8cd22905.jpg http://i440.photobucket.com/albums/qq129/subwooferbone/null_zpsbb34ca74.jpg -- Joachim ...   10-13-2013 04:26 pm

Projects > 18711 "Miss Jensen" (129 replies - 245987 views)

And the wheels are on the car! http://i440.photobucket.com/albums/qq129/subwooferbone/null_zps50e59f31.jpg Brakes will go on after the season ends, still a few weeks left, I hope, but winter is approaching ...   10-11-2013 08:21 pm

Projects > 18711 "Miss Jensen" (129 replies - 245987 views)

... and here they come! Picked the new rims up today, so I just had to try them on to see what they will look ...   10-09-2013 08:07 pm

Wheels > Stock wheel offset (19 replies - 36283 views)

Picked up the new rims today, will get some tyres for them ASAP! I ordered 7x15" ET05 rims, clearance looks good. No need to space ...   10-09-2013 08:00 pm

Carburetors > DHLA 45 Idle Mixture Setting Help (17 replies - 31566 views)

Squirt a bit of oil into the offending cylinder and retest. If that helps, the problem is with the rings, otherwise the valves are leaking. ...   09-25-2013 08:22 pm

Carburetors > DHLA 45 Idle Mixture Setting Help (17 replies - 31566 views)

Jensen Healey wrote: Since Lotus/ Jensen couldn't even tune these carbs properly at the factory your best bet is to use the jetting that works for ...   09-25-2013 08:25 am

Carburetors > DHLA 45 Idle Mixture Setting Help (17 replies - 31566 views)

Www.diyautotune.com is a reliable source. For a carbed application, the Innovate LM2 should fit the bill, AFAIK it can be connected to the coil for ...   09-24-2013 08:47 pm

Carburetors > DHLA 45 Idle Mixture Setting Help (17 replies - 31566 views)

IMNSHO you should get yourself a wideband O2 sensor before you start messing with jetting. That way you have a way of identifying the problems ...   09-24-2013 05:44 pm

Carburetors > DHLA 45 Idle Mixture Setting Help (17 replies - 31566 views)

First of all, are your carbs accurately balanced? I use a CarbTune II (http://www.carbtune.com/) for this purpose. If memory serves me correct, a half decent starting ...   09-24-2013 05:24 am

Suspension > Fitting rear Superpro bushes (27 replies - 50530 views)

No replacement, the cotton reel shape keeps it in place. There are really two ways to get the shells out; hydraulic press or hacksaw. Choose ...   09-21-2013 09:50 pm


 Current time is 07:37 am
 First Page Previous Page  1  2  3  4  5  6  7  8  9  10  ...  Next Page Last Page


UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems