Joel, likewise sorry to hear of your misfortune. At least you are ok........... ...   10-08-2008 08:22 pm

Dave, one way to verify the coolant temp compared to the gauge is to use an infared temp sensor on the back of of the ...   09-19-2008 02:23 am

Jody, I am sure a lot of us relate to your "oversight". I know I do. Been There Done That on several occasions! Thanks for the ...   08-27-2008 01:57 am

John glad you are ok.   ...   08-17-2008 06:51 pm

You could also install a valve in the supply side heater hose located in the engine compartment if there is room. When closed this will ...   07-25-2008 09:56 pm

On the engine side of the fire wall, remove the two heater hoses from the heater core barbs and splice them together. You can find ...   07-12-2008 07:57 pm

Try finding a Burroughs or Robinair guage on ebay or google. Model numbers that are known to work for the Lotus 907 are (Burroughs) BT-33-86J, ...   07-06-2008 03:26 pm

Dan, welcome to the world of JH's. You'll find this forum a valuable resource. I have owned my 74-JH since the summer of 2005. Pix of ...   05-23-2008 09:18 pm

If you do happen to overtighten as I did send your dizzy to the shop listed below. He rebuilt mine and installed a steel collar. Excellent ...   04-30-2008 10:19 pm

I purchased elastic strap material (for cheap) from an auto upholstery shop and my wife sewed the loop ends on her machine. I used the old ...   04-27-2008 08:06 pm

Jody, Well done! I look forward to future project documentations. John ...   04-24-2008 09:01 pm

I had a Stayfast top by AA Best professionally installed and am very pleased with it.  Pix on the JHP Photo Gallery, Minnesota.  John   ...   11-06-2007 01:58 pm

In my opinion you won't be dissapointed with Jeff's work. I live about 25 miles from him so was able to see his shop, equipment ...   09-29-2007 01:25 pm

How about reinstalling the points? ...   09-28-2007 11:36 pm

I've also had my distributor rebuilt by Jeff and recommend him. Required new bushings and replacing the aluminum securing collar with steel. Some one overtorqued...........He ...   09-27-2007 08:57 pm

Mike, I think I have a pair incl hardware less mounting screws. Send me a pm I'll go look and pm you a picture and ...   08-31-2007 10:29 pm

Got the dizzy rebuilt and recurved by Jeff Schlemmer at Advanced Distributors jschlemmer1@comcast.net, 612-804-5543. He also repaired the clamp collar I damaged and fine tuned ...   07-21-2007 12:09 pm

Great lead! Thanks Ron! ...   07-09-2007 01:58 am

Looks like I am in the market for a 25D4. Thanks again for all the excellent knowledge and advice. ...   07-08-2007 10:23 pm

Great insight. Thanks to both! John ...   07-08-2007 02:51 pm

John Thanks. I balanced the carbs with my Carbtune after installing the Pertronix and all was ok actually. I am currently running 55 idle jets. Thats ...   07-07-2007 09:45 pm

I've completed the installation of a Pertronix and MSD on 18309. Plugs are gapped at .35. Dellorto 45's spec 5. Starts and idles fine. I ...   07-07-2007 07:01 pm

Thanks Mom, I'll get "r" done. Your son ...   05-19-2007 02:40 am

Paul, congratulations and enjoy the ride! JHPS is a great organization. I know my JH sure runs better thanks to the fine folks sharing their knowledge and ...   04-28-2007 07:50 pm

Hi Dave, actually I saw Milwaukee in the left margin after I sent the email. The Mpls Lotus car club I belong to likes to ...   04-27-2007 05:28 pm

Steve, I have a pair of strombergs that I've never run fuel through. They sat idle on the car in Phoenix for 15 years before ...   04-25-2007 10:33 pm

Search the JHPS site for voltage stabilizer. There are some photos and good reference infor for you. Basically its behind the fuel and temp gauges. ...   04-25-2007 01:15 am

 I bought one in Oct 2005 from Edgar Esslinger at esslinger@charter.net on ebay for $20.00. Works great so far. It was listed as a Triumph ...   03-01-2007 09:21 pm

http://cgi.ebay.com/Dellorto-DHLA-Weber-DCOE-tuning-manual-NEW_W0QQitemZ300065722756QQihZ020QQcategoryZ48444QQssPageNameZWDVWQQrdZ1QQcmdZViewItem Try this link to purchase an excellent book on Dellorto Carbs ...   01-04-2007 06:47 pm

I had my Dellorto manifold modified to accept the hose fitting. Works great. Good luck with your project. ...   12-22-2006 08:38 pm

Vin...1111-18309  w/orig steel bumpers and 4 spd Condition...Mechanically restored, Dellorto 45’s, Body is orig and excellent Engine #...B74 09 9084 Mfg Date...Oct-8-74  (8-10-74 on door plate) 63k orig miles, ...   11-14-2006 08:51 pm

FYI, I purchased a stayfast top from AA Best for 18309 last fall and had it installed this spring. I am very pleased with the ...   10-07-2006 03:17 pm

Following is from the owners manual: "Unfasten the seven press studs and detach the velcro held side panels at the rear of the soft top. ...   09-08-2006 09:06 pm

I got one from Delta this spring and it works great. About $10.00 IIRC ...   09-08-2006 08:49 pm

Norm, get the Des Hammill book if you don't have it. "How to Build and Power tune Weber & Dellorto Carbs" Ebay or Amazon. Per ...   08-20-2006 01:52 pm

Hey Jon, where did you get the servo non return valve? 18309 has the symptom you described and corrected by replacing the valve. Thanks John ...   08-08-2006 04:40 pm

I also have had mine done by gas tank renew. Looks and  works great so far. Good luck John ...   07-25-2006 10:08 pm

Congratulations! Its been fun and educational "watching" your progress. I know I've learned from your experiences. Its great to feel and hear a 907 come back ...   07-04-2006 02:25 pm

Following is how Tim Engle explained and set up 18309 after bringing it back to life after sitting for 15 years. So far no issues at all.  ...   06-22-2006 08:06 pm

I used a 1/4" wool type insulator backed with foil on one side. Easy to cut and fit. Basically its a water heater type wrap. ...   06-22-2006 07:32 pm