Well, this is a much better grease method explanation: http://www.youtube.com/watch?v=uPj2eZ7Eofs&feature=endscreen&NR=1 Pete Bahr YELODOG ...   01-15-2012 04:07 pm

Hi Mitch, My engine is a repair (for burnt pistons) of an engine that Richard had in one of his cars.  I would have sent him ...   12-13-2011 11:59 pm

I have no problem with dowling the lower sub-frame in the engine, but I see the oil pan flapper as a not-needed extra cost if ...   12-13-2011 04:53 pm

About the only thing that you can adjust on the JH is the Clutch Cable. YELODOG ...   11-12-2011 12:51 am

About the only thing that you can adjust on the JH is the Clutch Cable. YELODOG ...   11-12-2011 12:51 am

The Jensen boys used Lucas electrical bits - known to be the worst in the world. Take the Ignition Switch for example: It is a ...   10-25-2011 03:30 pm

OK, got it. With that part bad, the rear of the Bracket can move around. It actually should not move too much unless the bearings ...   10-20-2011 03:13 pm

Wazza "rear mount" ? Pete ...   10-20-2011 01:19 am

Hey Brett, thanks for the kudos... I've rebuilt a total of about 10 of these over the past few years and receipants have been very pleased ...   09-11-2011 03:14 pm

I love solid lubricants like graphite and MoS2. Grainger makes a spray can with MoS2 in an evaporating carrier. The spray penetrates very small spaces ...   07-28-2011 03:17 am

Seems that all the new car dealers use lithium grease (pink) for that application. YELODOG ...   07-27-2011 08:22 pm

Joachim, you have to get SOMEONE ELSE to do it ! ! ! ...   07-21-2011 08:23 pm

You probably sheared the Nylon column collapse bits... I replaced mine with soft copper wire ...   07-21-2011 07:34 pm

Just use an air-powered cut-off wheel and grind the bolt off. Works every time. YELODOG ...   07-21-2011 12:37 pm

Well, I HOPE SO ! ! ! ! ...   07-01-2011 03:37 am

Joachim beat me to the question about an air leak......... YELODOG ...   06-27-2011 05:53 pm

Gee whiz, six JH with Webber / Dellorto setups. I'm impressed. Great photos, and a beautiful venue. Pete ...   06-26-2011 06:40 pm

Looks absolutly fantastic ! ! ! ! ...   05-10-2011 01:01 am

Fantastic ! ! ! ! YELODOG ...   05-01-2011 10:27 pm

For the HTD Lotus belts and gears, you could try R.D.Enterprises.  Ray Psulkowski is a well respected Lotus parts dealer. rdent@rdent.com  I've had good luck at ...   04-29-2011 04:28 am

I finally got mine installed with the help of Franks information. Work great, and keep the Bonnet open nice and wide. YELODOG ...   03-31-2011 01:17 am

Thanks Brett.  Please do not tell anyone how easy it is, as I'm already flooded with work ! ! ! ! YELODOG ...   03-21-2011 03:54 pm

Hi guys, I'm in process of rebuilding several of the 5spd Shifter assemblies. Another JH owner is interested in joining the group, but he will need to ...   03-21-2011 01:32 am

As I recall, the keyway is off-set on the bottom, and thus will only seat when rotated to the correct position.  It can not be ...   02-27-2011 06:07 pm

I have to agree with Mike.  If the driveshaft has the correct parts and is made by a proper shop, and tested / balanced to ...   02-21-2011 04:17 am

Hi Mart, Welcome to the Forum.  Don't hesitate posting questions, as you are more than likely to get correct answers. YELODOG ...   02-16-2011 08:58 pm

I'm sure you will be flamed. But, how can a LUCUS product ever screw up a British car? On all my cars I always add MoS2 to ...   02-12-2011 03:59 pm

Well, that's the second time I've been wrong.  I remember the first in 1962...........  ...   02-09-2011 01:41 am

Hi Pete, Wonder of wonders.  Thanks to jgreen, I have in my hand a damper with the stroke that you described earlier.  First one that I've ...   02-08-2011 07:41 pm

Just when do yoy get the noise????????? YELODOG ...   02-06-2011 04:04 am

My registration went to Post yesterday.  Don't want to miss that event, for sure. YELODOG ...   02-03-2011 04:09 pm

Joachim, That engine looks pretty bad.  I have a head if you want to pay for shipping.......... YELODOG ...   01-30-2011 12:59 am

Hi guys, I have a need for the Shifter Assy that fits Getrag five speed Transmissions.  Don’t want the tranny, just the Shifter Assy. If you know ...   01-26-2011 03:36 am

OK folks, I now have enough orders to start a build.  Cores will be going to the machine shop in a few weeks, so if ...   01-24-2011 08:09 pm

Hi Guys, Like I said above, I'm not pushing this item, but rather just trying to support the JH community. Anyone that is seriously interested must send ...   01-20-2011 04:23 am

When I did YELODOG, it had been in a garage for 10 years and all the brake lines/components were frozen or gunked up. I opened all ...   01-19-2011 04:50 am

Brett, thanks for the kudos....... As you know, I'm happy to support the JH owners. You know the three guys that got the last batch ...   01-19-2011 04:46 am

Please heed the warning: "Of course, the today manufacturers can always change the compound, and might do so as long as it is compatible with the ...   01-18-2011 04:04 pm

Jody, Now you've opened a can-of-worms - using DOT-5 silicone fluid.  I'm certain that the both of us are going to get blasted ! ! ! ...   01-18-2011 03:11 am

Hi Pete, Mounting for the LHD cars is identical to your RHD photos.  All the cars were built the same except the GT, which doesn't have ...   01-18-2011 03:01 am