Home 
> Jensen Healey & Jensen GT Tech > Wheels > Alternative JH Wheel sources

 Moderated by: Greg Fletcher  
AuthorPost
discogodfather
Member


Joined: 09-17-2007
Location: San Francisco, California USA
Posts: 221
Status: 
Offline
Everyone knows Minilite and panasport, my pocketbook dosen't go up to those numbers most of the time.  When I was faced with needing a new set of wheels for a custom project (my JH is flared) I found two that I hadn't seen anyone talking about:

1) Diamond Racing wheels (http://www.diamondracingwheels.com/)

A simple, no-nonsense all steel stamped wheel nascar style.  They have a few lightweight options including 12-20lbs wheels, which are great for a steel wheel.  My 15x8 weight only 16lbs.  They will make the wheel in any offset you need and have the rare 4x4 pattern.  Shipped to my door for around $80 a wheel and took only 3 weeks.  These are great wheels- who says you need aluminum and magnesium when your on a budget?  Make good backups.

2) Superlite wheels (http://www.packracingproducts.com/acatalog/Pack_Racing_Products_Superlite_Wheels_2.html)

Nice copies of minilite stlye wheels made in Australia from what I understand.  Decent quality castings and low cost ($150 a wheel).  Got mine in 4x4 no problem, and with a hard to get backspace.  Great selection if you need 13" wheels up to 16" for the JH, don't know if they make an exact replacement sized for the stock wheels. 


Chris Morlock

Attachment: Wheels.JPG (Downloaded 102 times)

colinw59
Member


Joined: 02-14-2006
Location: Bloomfield/Hebron, Connecticut USA
Posts: 147
Status: 
Offline
Hi Chris

             I used Superlites on #15851, they look great. Much brighter and sportier looking than the stock rims.

http://jhppg.com/gallery/74-Jensen-Healey-15851/2006_0522_13

http://jhppg.com/gallery/74-Jensen-Healey-15851/2006_0522_14

Judson Manning
Member


Joined: 03-14-2005
Location: Atlanta, Georgia USA
Posts: 406
Status: 
Offline
Chris,

who did your flares?  I have to do the same for my e-prod car and body-work is not my area of expertise.  suggestions?

Judson

discogodfather
Member


Joined: 09-17-2007
Location: San Francisco, California USA
Posts: 221
Status: 
Offline
Hey Judson,

Fender flares are a difficult task on the Healey.  The stock fender rimming is terrible, too thin and the geometry does not lend well to flaring.  My flares where done by a retired professional restoration and fabrication expert that owned the car before me.

He went to insane lengths to flare these fenders.  He literally worked the metal into a shape that was consistant with a good tangency to the body, and then welded metal in while working it all together.

His process was:

1) Didn't remove any metal
2) Contructed a special fender "roller" that bolted to the spindles and used delrin rollers at the tips of the arm to literally work the metal into the good tangency to the body (kind of like a can opener pushing the rim of the can outwards as it opens the can)

note: I remember he used went to great lengths to make this "fender roller".  About a year ago, I opened an Eastwood catalog and they had a very similar rig selling for several hundred US dollars.

3) Welded a rim in a flat butt weld in 18 guage parallel to the straight rolled shape of the flare (the extension piece was around 1.5" in length)

4) Used another rolling tool (I forget if it was custom or not) to hem the newly welded metal around in a circle.  This was very key to creating a strong, factory looking flare.

5) Sanded, hammered, and worked the metal into a smooth shape.  No bondo!  Absolutetly no bondo. 

All in all it was at least 50 hours of labor and I thought he was crazy for doing it, but it looks unique.  It allows me to run 8" wheels (could go to 10" in rear) with a 4 inch backspace- heavily inset wheels.  This is not a good performance thing, as any wheel specialist or engineer will tell you it is better to have a larger backspace to help natural balance the wheel.  Even with good wheel balancing I still get a shake at only at 60 mphs, no other speed.  Spacers and things might help that problem, but it dosen't solve the engineering issue.  For a great explanation on this phenomenon, go to:

http://www.diamondracingwheels.com/Terms-BS.htm

Look at the "backspace limits" section.  Don't get me wrong, I love the extra rubber, and it makes it nearly impossible to break loose even under the hardest turns- would be fantastic for racing.  Also opens 225/50 and 245/50 15" tires to the Healey- lots of great choices out there in those sizes. 

Going back to the flares, I would recommend looking at some bolt up fiberglass flares for racing.  They are cheap, look funky, and cost nothing compared to fabricating and maintaining steel fenders in a racing environment. 

If you really want steel, the only adivce I can give you is to look possibly at a Porsche body shop that has some old school guys still working (I bit of a long shot).  In the 60's and 70's the 911 had the same problem as the healey- anemic flares.  Tons of people wanted more rubber (and wanted their regular 911's to look like the 930 turbo) and steel flares are common additions to older 911's.  Look for a shop with steel experience- fiberglass flares for the Porsche where common and of low quality usually. 

Just say no to bondo!


Chris




Attachment: Flares copy.jpg (Downloaded 80 times)



UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems