Home 
Home Search search Menu menu Not logged in - Login | Register
> Jensen Healey & Jensen GT Tech > Body & interior stuff > Gas Struts For Your Bonnet (Hood)

 Moderated by: Greg Fletcher
New Topic Reply Printer Friendly
Gas Struts For Your Bonnet (Hood)  Rate Topic 
AuthorPost
 Posted: 03-24-2005 01:43 pm
  PM Quote Reply
1st Post
Mitch Ware
Member


Joined: 03-12-2005
Location: Albany, New York USA
Posts: 204
Status: 
Offline
At the 2004 Jensen Nationals in Nashville Frank Schwartz shared the information for replacing the stock hood prop rod with gas struts. I followed Franks' instructions and did the modification to my car. It works great! Purists may poo-poo the change, but I doubt there are really that many Healey's and GT's out there that have everything completely stock.

Strut Instructions

Mitch Ware

1974 JH-5 #111119670

1971 TR-6 #CC66950LO

Back To Top PM Quote Reply  

 Posted: 03-28-2005 01:42 pm
  PM Quote Reply
2nd Post
brino
Member
 

Joined: 03-12-2005
Location: Keswick, Ontario Canada
Posts: 11
Status: 
Offline
Now I'm ressembling my car returned from the body shop where among other things they did a wonderful job repairing the kinked hood. I decided not to reinstall the stock strut and visited the local wrecking yard an acquired a rigid support rod and bracket from an older Ford Tempo. It's installed now & works great as it supports the hood at the front and allows the hood to be raised about 4" higher than the standard set up. I'd recommend this route to all.

Back To Top PM Quote Reply

 Posted: 03-28-2005 02:39 pm
  PM Quote Reply
3rd Post
Mark Rosenbaum
Member


Joined: 03-12-2005
Location: Kingman, Arizona USA
Posts: 532
Status: 
Offline
Got a photo of how you did it?  My factory support rod is going to fail some day soon and I'm considering alternatives to just replacing it.

Back To Top PM Quote Reply  

 Posted: 03-28-2005 03:05 pm
  PM Quote Reply
4th Post
brino
Member
 

Joined: 03-12-2005
Location: Keswick, Ontario Canada
Posts: 11
Status: 
Offline
Can do. I'll post a photo in the next couple of days.

Back To Top PM Quote Reply

 Posted: 03-29-2005 08:58 pm
  PM Quote Reply
5th Post
brino
Member
 

Joined: 03-12-2005
Location: Keswick, Ontario Canada
Posts: 11
Status: 
Offline
Sorry for delay in pic Mark. I'm waiting for a friend to pop over with a digital camera. Should I e-mail it to you or post it here? Shouldn't be more than a couple more days.

Back To Top PM Quote Reply  

 Posted: 03-29-2005 11:38 pm
  PM Quote Reply
6th Post
Mark Rosenbaum
Member


Joined: 03-12-2005
Location: Kingman, Arizona USA
Posts: 532
Status: 
Offline
I'm sure the folks here would appreciate seeing how you installed the support, so I suggest posting photos here.  If you also send me an email with photos then I won't have to figure out how to download stuff from the board.

Back To Top PM Quote Reply

 Posted: 04-27-2005 12:08 am
  PM Quote Reply
7th Post
kneff
Member
 

Joined: 04-06-2005
Location: San Jose, California USA
Posts: 21
Status: 
Offline
How high do these struts raise the hood? In the '74 J-H I bought this weekend (from Tim Fultz), someone in the past replaced the original hood strut with an old-fashioned prop rod. It works fine, but it doesn't raise the hood far enough to avoid backaches.

What I've been using are a pair of wooden dowels, one on each side, to prop the hood (not quite) as high as it will go. What I'd REALLY like is a pair of gas struts that raised the hood nearly as high as the springs will allow.

Back To Top PM Quote Reply  

 Posted: 04-27-2005 01:26 am
  PM Quote Reply
8th Post
brino
Member
 

Joined: 03-12-2005
Location: Keswick, Ontario Canada
Posts: 11
Status: 
Offline
Measuring perpendicular from the top of the rad support to the underside of the hood is 42" with my old style prop installation. That gives a lot more room than the stock set up. I've been meaning to get a digital phot taken & post it here, but I haven't figured out how do do that yet. In any event my installation is quite simple. I mounted the support strut base about 7" fore of the position of the original strut and the top of the brace hooks nicely into the hole on the front corner of the hood. Looks & works great.

Back To Top PM Quote Reply

Current time is 12:40 pm  
> Jensen Healey & Jensen GT Tech > Body & interior stuff > Gas Struts For Your Bonnet (Hood) Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems