Home 
Home Search search Menu menu Not logged in - Login | Register
> Jensen Healey & Jensen GT Tech > Body & interior stuff > Where do the body panel Data Plates go?

 Moderated by: Greg Fletcher
New Topic Reply Printer Friendly
Where do the body panel Data Plates go?  Rate Topic 
AuthorPost
 Posted: 07-04-2020 04:37 am
  PM Quote Reply
1st Post
discogodfather
Member


Joined: 09-17-2007
Location: San Francisco, California USA
Posts: 221
Status: 
Offline
After 20 years of running without original ID plates after the body was completely stripped and redone, I got a set of repro data plates from Greg, marked with my chassis #.

Small problem- where do they go? I have some pictures of other cars and the emissions plate and the smaller plate that reads "Jensen Healey" in bold at the top sits next to it in front of the radiator on the shroud.

The other smaller plate goes on the drivers door? Or on the door panel on the body?

Pics would be awesome but any verbal directions are good too.

Back To Top PM Quote Reply  

 Posted: 07-05-2020 04:15 am
  PM Quote Reply
2nd Post
Dakota123
Member
 

Joined: 03-20-2009
Location: Colorado USA
Posts: 185
Status: 
Offline
10628 doesn’t have the top right tag, and it looks like there is one missing on the radiator support (or maybe that’s where the emissions tag was originally (can’t make out the emissions tag unfortunately).

Attachment: 1E9022F6-6685-4592-B401-65FDD68AB4F6.jpeg (Downloaded 67 times)

Back To Top PM Quote Reply

 Posted: 07-05-2020 04:18 am
  PM Quote Reply
3rd Post
Dakota123
Member
 

Joined: 03-20-2009
Location: Colorado USA
Posts: 185
Status: 
Offline
Dakota123 wrote:
10628 doesn’t have the top right tag, and it looks like there is one missing on the radiator support, or maybe that’s where the emissions tag was originally (can’t make out the emissions tag unfortunately).

Attachment: 441B63E3-F272-4C6F-90DC-25F08FEA3D99.jpeg (Downloaded 66 times)

Last edited on 07-05-2020 04:18 am by Dakota123

Back To Top PM Quote Reply  

 Posted: 07-05-2020 02:30 pm
  PM Quote Reply
4th Post
mtechwim
Member
 

Joined: 12-07-2019
Location:  
Posts: 53
Status: 
Offline
First picture of Dakota, Mine is sitting on the door On the opposite site, and not on the body.

Can’t upload the foto.

Last edited on 07-05-2020 02:36 pm by mtechwim

Back To Top PM Quote Reply

 Posted: 07-30-2020 05:37 pm
  PM Quote Reply
5th Post
noomg
Member
 

Joined: 08-02-2018
Location: Long Beach, California USA
Posts: 414
Status: 
Offline
Disco,

It looks like you've got a set of '73 plates(3), one went on the driver side door(VIN plate), the other two(big one and JENSEN-HEALEY small one)went on top of the radiator. The '74 had only two plates, the door plate and the two radiator plates which were combined into one.

Dakota,

While I'm not one to tell a man how to setup his car, you do realize that the back door sill plate is stainless steel and when stripped and polished it's not only very scuff and scratch resistant but also pleasing to the eye. It was how they originally rolled out of the factory.

Back To Top PM Quote Reply  

 Posted: 08-16-2020 04:12 am
  PM Quote Reply
6th Post
discogodfather
Member


Joined: 09-17-2007
Location: San Francisco, California USA
Posts: 221
Status: 
Offline
Thanks guys, finally got around to install using 1/16" aluminum rivets. Looks good. Thanks to Greg for making them too!


Back To Top PM Quote Reply

 Posted: 08-16-2020 04:14 am
  PM Quote Reply
7th Post
discogodfather
Member


Joined: 09-17-2007
Location: San Francisco, California USA
Posts: 221
Status: 
Offline
Also on the install for anyone else attempting this:

I feel like it's a great idea to paste a very thin layer of silicone on the back of these plates so that when moisture and dirt floats in, there is a barrier for it. The plates tend to trap this stuff and sit forever, then the rust spot is observed. At best, it ruins the area of paint over time. The aluminum and steel expand and contract differently with heat, and with a little dirt there you have a small example of sandpaper.

Back To Top PM Quote Reply  

Current time is 12:27 pm  
> Jensen Healey & Jensen GT Tech > Body & interior stuff > Where do the body panel Data Plates go? Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems