Home 
Home Search search Menu menu Not logged in - Login | Register
> Jensen Healey & Jensen GT Tech > Carburetors > fuel leak stromberg

 Moderated by: Greg Fletcher
New Topic Reply Printer Friendly
fuel leak stromberg  Rate Topic 
AuthorPost
 Posted: 05-13-2020 09:54 pm
  PM Quote Reply
1st Post
Joenpate56
Member
 

Joined: 12-01-2015
Location:  
Posts: 43
Status: 
Offline
I have tried tightening by hand the plug seem to turn in both directions without tightening I assume its the o ring seal or just loose. How is the plug secured.

Back To Top PM Quote Reply  

 Posted: 05-13-2020 10:17 pm
  PM Quote Reply
2nd Post
mtechwim
Member
 

Joined: 12-07-2019
Location:  
Posts: 53
Status: 
Offline
Do you mean the big plug in the center of the bowl?

If so be very careful with it it has plastic parts, I could make a foto in the morning ( in in the middle of the night now in Holland)

I am buzzy refurbishing 2 now.

There is a o ring seal.

Back To Top PM Quote Reply

 Posted: 05-14-2020 12:31 am
  PM Quote Reply
3rd Post
Joenpate56
Member
 

Joined: 12-01-2015
Location:  
Posts: 43
Status: 
Offline
yes that is the one. a foto would be great

Back To Top PM Quote Reply  

 Posted: 05-14-2020 01:59 am
  PM Quote Reply
4th Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 617
Status: 
Offline
If the plastic plug on the very bottom center of the bowl is leaking, DO NOT ATTEMPT TO START YOUR CAR. the rear carb sits right over the starter/solenoid, and it would be INSTANT FIRE.
If you haven't rebuilt the carbs in a while or run the car in a while, just rebuild the carbs(takes me 5-6 hours).

Back To Top PM Quote Reply

 Posted: 05-14-2020 10:12 am
  PM Quote Reply
5th Post
mtechwim
Member
 

Joined: 12-07-2019
Location:  
Posts: 53
Status: 
Offline
Here is are some foto’s

Attachment: FF06D90B-92F4-4B92-AAC7-4CCA1FF5800D.jpeg (Downloaded 50 times)

Last edited on 05-14-2020 12:43 pm by mtechwim

Back To Top PM Quote Reply  

 Posted: 05-14-2020 12:45 pm
  PM Quote Reply
6th Post
mtechwim
Member
 

Joined: 12-07-2019
Location:  
Posts: 53
Status: 
Offline
Here is an other model from kopper, no idee what the difference is.this one fare less fragile. If possible I would like to use this one in stead of the plastic one.

Attachment: 2D672E47-A17E-413D-90FB-A231FE3CD74C.jpeg (Downloaded 50 times)

Last edited on 05-14-2020 12:46 pm by mtechwim

Back To Top PM Quote Reply

 Posted: 05-14-2020 01:59 pm
  PM Quote Reply
7th Post
Joenpate56
Member
 

Joined: 12-01-2015
Location:  
Posts: 43
Status: 
Offline
Thanks for all the information. Luckily I noticed the leak before I got the car started. It was the front carb. I have ordered the o rings. How difficult is it to pull the plug out. Should I jut order a new one?

Back To Top PM Quote Reply  

 Posted: 05-14-2020 03:34 pm
  PM Quote Reply
8th Post
mtechwim
Member
 

Joined: 12-07-2019
Location:  
Posts: 53
Status: 
Offline
The top one, is easy but becarvul, clean outside, spray some tread lube around, wait a bit and with a small screwdriver pull it out. Not on one side but around so I comes strait out.

If you miss some plastic parts you have to open the bottom.

Back To Top PM Quote Reply

 Posted: 05-14-2020 03:47 pm
  PM Quote Reply
9th Post
mtechwim
Member
 

Joined: 12-07-2019
Location:  
Posts: 53
Status: 
Offline
The big kopper one is ideal when you want to replace the jet.

Back To Top PM Quote Reply  

 Posted: 05-15-2020 05:26 pm
  PM Quote Reply
10th Post
Tom Bradley
Member
 

Joined: 07-15-2013
Location:  
Posts: 200
Status: 
Offline
If the bottom o-ring is leaking, then other rubber parts may be going bad as well. I recommend taking off the top on one of the carbs and check the condition of the rubber diaphragm. If it looks to be going bad, you might want to get a couple rebuild kits.

Back To Top PM Quote Reply

 Posted: 05-15-2020 05:35 pm
  PM Quote Reply
11th Post
Joenpate56
Member
 

Joined: 12-01-2015
Location:  
Posts: 43
Status: 
Offline
thanks for all the help. my orings should be here today or tomorrow. ill let you know how it goes. I have already removed the plug so it should be simple

Back To Top PM Quote Reply  

 Posted: 05-15-2020 05:38 pm
  PM Quote Reply
12th Post
mtechwim
Member
 

Joined: 12-07-2019
Location:  
Posts: 53
Status: 
Offline
I found out dat also the rubber seals from the throttle axle were shot.
So I would advice a full refurbishment of the carbs to.

Back To Top PM Quote Reply

Current time is 12:10 pm  
> Jensen Healey & Jensen GT Tech > Carburetors > fuel leak stromberg Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems