Home 
Home Search search Menu menu Not logged in - Login | Register
> Jensen Healey & Jensen GT Tech > Electrical & Instruments > Wiring Harness Installation

 Moderated by: Greg Fletcher
New Topic Reply Printer Friendly
Wiring Harness Installation  Rating:  Rating
AuthorPost
 Posted: 09-18-2014 07:05 pm
  PM Quote Reply
1st Post
fogrocker
Member
 

Joined: 01-21-2014
Location: Bothell, Washington USA
Posts: 6
Status: 
Offline
I am at the point of installing my wiring harbness and have nop clue as to the route it originally took....

Anyone have some pictures of one insatalled?

74 JH

thanks

Patrick

wheelsgodown@gmail.com

Back To Top PM Quote Reply  

 Posted: 09-19-2014 02:03 pm
  PM Quote Reply
2nd Post
Brett Gibson JH5 20497
Member
 

Joined: 03-17-2005
Location: Hilton, New York USA
Posts: 713
Status: 
Offline
Now that is funny, I had the same issue but luckly I have another JH and was able to go to that and check the routing, did a bit of moving stuff but now have it in the same place. I will send you a couple of photo's to your e-mail.

Brett

 

Back To Top PM Quote Reply

 Posted: 09-19-2014 02:20 pm
  PM Quote Reply
3rd Post
fogrocker
Member
 

Joined: 01-21-2014
Location: Bothell, Washington USA
Posts: 6
Status: 
Offline
thank you

Back To Top PM Quote Reply  

 Posted: 11-08-2016 04:28 pm
  PM Quote Reply
4th Post
DonBurns
Member
 

Joined: 09-18-2015
Location: Fullerton, California USA
Posts: 47
Status: 
Offline
Brett-

I would also love to get some photos showing original harness routing, especially under the dash. I have a new main harness on order, have already replaced the engine and instruments. My main has been fairly butchered over the years. None of the bend over tabs seem to be near the harness now, so I'm not sure how it used to be!

Thanks-

Don Burns

Back To Top PM Quote Reply

 Posted: 11-09-2016 01:37 pm
  PM Quote Reply
5th Post
Brett Gibson JH5 20497
Member
 

Joined: 03-17-2005
Location: Hilton, New York USA
Posts: 713
Status: 
Offline
PM me with your e-mail and I will send you a few photo's.

Brett

Back To Top PM Quote Reply  

 Posted: 11-10-2016 04:38 pm
  PM Quote Reply
6th Post
redracer
Member
 

Joined: 09-10-2012
Location:  
Posts: 120
Status: 
Offline
If you lay the harness on a large floor, most of the design will be obvious. The later harnesses (J-H #97764; first were #90587, then after chassis # 13350 were 97049, then #97764) have the nickel chrome(white with slate stripe) as opposed to the white with pink stripe) wire going from the tach to the coil, so be sure to test the reistance(!.5 ohms). If your car has a ballast resistor, then obviously you have one of the earlier harness(very little differences between the first two).

Back To Top PM Quote Reply

 Posted: 11-10-2016 08:52 pm
  PM Quote Reply
7th Post
Brett Gibson JH5 20497
Member
 

Joined: 03-17-2005
Location: Hilton, New York USA
Posts: 713
Status: 
Offline
I have the photo's but not your e-mail address ? your PM did not include it.

Last edited on 11-11-2016 04:55 pm by Brett Gibson JH5 20497

Back To Top PM Quote Reply  

Current time is 03:27 am  
> Jensen Healey & Jensen GT Tech > Electrical & Instruments > Wiring Harness Installation Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems