Home 
Home Search search Menu menu Not logged in - Login | Register

 Moderated by: Greg Fletcher
New Topic Printer Friendly
Door Hinge Screw Heads  Rating:  Rating
AuthorPost
 Posted: 05-29-2014 05:20 am
   
1st Post
Jensen Healey
Super Moderator


Joined: 03-11-2005
Location: San Anselmo, California USA
Posts: 976
Status: 
Offline
I am trying to adjust the door hinges on the Red Fox and the Phillips (Pozidrive?) screw heads are gigantic. Does a #4 Phillips fit?
I don't want to drive all over town to find one and find out it doesn't fit.
Thanks,
Kurt
JH 13148 (runs well) and 19753 project

Back To Top    

 Posted: 05-30-2014 06:48 am
   
2nd Post
Jensen Healey
Super Moderator


Joined: 03-11-2005
Location: San Anselmo, California USA
Posts: 976
Status: 
Offline
Well, I managed to purchase a #4 phillips bit at the local Ace Hardware. The fit wasn't good but it did the job.
I'm now trying to adjust the hinge side of the door upward. Not sure how that works.
Kurt

Back To Top  

 Posted: 06-02-2014 05:23 am
   
3rd Post
answerman
Member
 

Joined: 09-10-2012
Location: Little Chute, Wisconsin USA
Posts: 381
Status: 
Offline
I used a #3 Phillips which seemed to work ok to get them apart, but then I went across the street to the hardware store and got socket head Allen screws to replace. Much easier to torque.

As far as adjusting, what I did was to get all the screws in loosely and then put a hydraulic floor jack with a towel over it under the part of the door I wanted to lift.

Back To Top    

 Posted: 06-06-2014 09:26 pm
   
4th Post
redracer
Member
 

Joined: 09-10-2012
Location:  
Posts: 119
Status: 
Offline
The adjustment for the doors is in the 3 bolts that go into the door itself. You will need to remove the door panel to access them

Back To Top  

 Posted: 06-07-2014 02:44 am
   
5th Post
Jensen Healey
Super Moderator


Joined: 03-11-2005
Location: San Anselmo, California USA
Posts: 976
Status: 
Offline
I will loosen the bolts with the door in the closed position and attempt to pry the hinge side upward while lowering the strike side. If I can get 1/8" it should help the wide gap at the top of the strike side.
Kurt

Back To Top    

 Posted: 06-07-2014 04:15 am
   
6th Post
redracer
Member
 

Joined: 09-10-2012
Location:  
Posts: 119
Status: 
Offline
You can adjust the 3 door volts so there is some friction and then try to set the door.

Back To Top  

 Posted: 06-08-2014 05:08 pm
   
7th Post
Jensen Healey
Super Moderator


Joined: 03-11-2005
Location: San Anselmo, California USA
Posts: 976
Status: 
Offline
Well, I managed to lever the door upward about 3/16". This door doesn't fit very well in the hole and I suspect the fenders were removed for the previous Earl Scheib paint job.

The outer handle is jammed and it must be opened from the inside. I need to remove the handle and lock for paint anyway so maybe I can figure out the problem. I blame it on the DPO!
Kurt

Back To Top    

Current time is 11:52 pm  
> Jensen Healey & Jensen GT Tech > Body & interior stuff > Door Hinge Screw Heads Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems