Home 
Home Search search Menu menu Not logged in - Login | Register

 Moderated by: Greg Fletcher
New Topic Reply Printer Friendly
Oil Pressure  Rate Topic 
AuthorPost
 Posted: 05-29-2013 01:00 am
  PM Quote Reply
1st Post
Mitch Ware
Member


Joined: 03-12-2005
Location: Albany, New York USA
Posts: 204
Status: 
Offline
No leaks anywhere, I have 80lbs of oil pressure at the filter (remote filter housing with electric sender unit there) but I have almost none at the spot on the cover where the tube to the gauge hooks up behind the starter.

Any ideas?

It isn't the hose to the gauge, that is fine. Take the hose off and start the engine, oil comes out, but not at a high pressure.

Mitch - #19670, #11002

Last edited on 05-29-2013 01:00 am by Mitch Ware

Back To Top PM Quote Reply  

 Posted: 05-29-2013 01:24 am
  PM Quote Reply
2nd Post
Mitch Ware
Member


Joined: 03-12-2005
Location: Albany, New York USA
Posts: 204
Status: 
Offline
Oh, forgot to mention.

Gauge was reading fine, then I did an oil & filter change. No big deal, drained oil, changed filter, added new oil. Started engine, no leaks anywhere, just no pressure reading where the oil gauge tube attaches.

Stuck a small piece of wire in the hole on the plate to make sure nothing was clogging it. It was clean.

Mitch

Back To Top PM Quote Reply

 Posted: 05-29-2013 11:06 am
  PM Quote Reply
3rd Post
Dan (Florida)
Member
 

Joined: 03-16-2005
Location: Ormond Beach, Florida USA
Posts: 97
Status: 
Offline
Just a wild opinion, was the filter an exact replacement for the previous filter?  The blockage seems to be at the filter.  Some filters have a check valve to prevent  leakback.  If the remote filter was hooked up backwards the check valve would go into  service and stop the flow.  Double check all of the inlets and outlets to be sure things are flowing in the right direction. 

I have been wrong before.   Dan

Back To Top PM Quote Reply  

 Posted: 05-29-2013 01:23 pm
  PM Quote Reply
4th Post
Mitch Ware
Member


Joined: 03-12-2005
Location: Albany, New York USA
Posts: 204
Status: 
Offline
Yeah, exact replacement filter. Oil flows from the adapter plate to the filter, then to the oil cooler and back to the adapter plate. I cracked the fitting at the oil cooler and oil spewed out, so it is flowing past the filter.

Thanks for tossing out a possible solution though.

Mitch

Back To Top PM Quote Reply

 Posted: 05-29-2013 02:42 pm
  PM Quote Reply
5th Post
pbahr
Member


Joined: 04-15-2005
Location: Phoenixville, Pennsylvania USA
Posts: 202
Status: 
Offline
Mitch,

I would remove the fitting where the oil pressure tube attaches and be certain that there is nothing cloging that passage.  That spot in on the high pressure oil gallery and certainly should see maximum pump oil pressure...........

YELODOG

Back To Top PM Quote Reply  

 Posted: 05-30-2013 01:29 am
  PM Quote Reply
6th Post
Jensen Healey
Super Moderator


Joined: 03-11-2005
Location: San Anselmo, California USA
Posts: 983
Status: 
Offline
Any luck Mitch?

If the hole in the cover isn't clogged, there's a major blockage in the oil gallery. Since that's highly unlikely it must be something easier.

Keep us posted,

Kurt

Back To Top PM Quote Reply

 Posted: 05-30-2013 12:18 pm
  PM Quote Reply
7th Post
Mitch Ware
Member


Joined: 03-12-2005
Location: Albany, New York USA
Posts: 204
Status: 
Offline
Ding, Ding, Ding, Ding, we have a winner!

It was a defective oil filter.

So today it's off to Lime Rock for the weekend to see if the car does more than look pretty.

Mitch

Back To Top PM Quote Reply  

Current time is 02:09 pm  
> Jensen Healey & Jensen GT Tech > Engine & Transmission > Oil Pressure Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems