Home 
Home Search search Menu menu Not logged in - Login | Register

 Moderated by: Greg Fletcher
New Topic Reply Printer Friendly
Metric?  Rate Topic 
AuthorPost
 Posted: 02-22-2013 08:41 pm
  PM Quote Reply
1st Post
sholdowa
Member


Joined: 01-03-2012
Location: Diamond Harbour, New Zealand
Posts: 21
Status: 
Offline
I've just suffered a catastrophic brake failure... Master cylinder needs a rebuild I think. First step was to drain the system, as the fluid is probably 10 years old anyway. Fronts... Np problem. Rears were a different matter, and the bleed nipple sheared off. So, time to replace both rear cylinders, I think.

Didn't have a brake spanner, so tried the best open ended spanner on the brake pipe, to no avail. The manual tells me these fittings are metric. Is this true? Am surprised for a Brit car of this vintage. Can anyone confirm this for me, please?

Also, does anyone have part nos for the wheel cylinders and master rebuild kits? I was going to take them in to be sure.

Back To Top PM Quote Reply  

 Posted: 02-22-2013 10:23 pm
  PM Quote Reply
2nd Post
JodyKerr
Member


Joined: 05-15-2006
Location: Tempe, Arizona USA
Posts: 217
Status: 
Offline
In the united states most brake fittings use SAE tools

Back To Top PM Quote Reply

 Posted: 02-22-2013 11:15 pm
  PM Quote Reply
3rd Post
Jensen Healey
Super Moderator


Joined: 03-11-2005
Location: San Anselmo, California USA
Posts: 977
Status: 
Offline
The brake fittings fit a 7/16" wrench. A standard open end spanner can distort the flare nut.



Proper brake wrenches have the head angled a bit so you can work around obstructions, a small but good investment.



The Lotus engine is metric except for the drain plug which is 3/4 Whitworth. The rest of the car is SAE.
 

Back To Top PM Quote Reply  

 Posted: 02-23-2013 03:32 am
  PM Quote Reply
4th Post
sholdowa
Member


Joined: 01-03-2012
Location: Diamond Harbour, New Zealand
Posts: 21
Status: 
Offline
I ended up using one of those fit all spanners - all teeth and tightens the harder you pull. The manual says 10mm but it's certainly 7/16 AF. Master cylinder is completely different too! It's got 08 646979175 G cast into it. Any idea what it is??

Glad I decided to take the bits down to the motor factors!

Last edited on 02-23-2013 05:33 am by sholdowa

Back To Top PM Quote Reply

 Posted: 02-25-2013 08:19 pm
  PM Quote Reply
5th Post
subwoofer
Member
 

Joined: 04-01-2008
Location: Sandefjord, Norway
Posts: 583
Status: 
Offline
have you googled the part number?

I got a new master cylinder a few years back, was listed for a Land Rover IIRC. Was about £50.

--
Joachim

Back To Top PM Quote Reply  

 Posted: 02-25-2013 08:44 pm
  PM Quote Reply
6th Post
sholdowa
Member


Joined: 01-03-2012
Location: Diamond Harbour, New Zealand
Posts: 21
Status: 
Offline
Hi Joachim,

Yes, it was the first thing I did, but no luck. I see a few that will fit... TR6, and a couple of Landy ones. I assume the difference is in the piston sizes, but can find no info on that. Also, as the car has been raced for decades, what changes may have been made anyway!

Brakes are standard apart from this, so am looking to replace a standard MC. As you say, the replacements are below GPB50, but when you add the quoted postage of GBP81, it makes your eyes water a bit!

Am working through Oz Landy sites now...

Cheers,

Steve

Back To Top PM Quote Reply

 Posted: 02-25-2013 10:17 pm
  PM Quote Reply
7th Post
subwoofer
Member
 

Joined: 04-01-2008
Location: Sandefjord, Norway
Posts: 583
Status: 
Offline
And I thought freight rates from the UK to Norway were bad...

I'll grab the chance while the Pound is weak to get myself a set of front and rear discs from Hispec.

--
Joachim

Back To Top PM Quote Reply  

 Posted: 02-28-2013 08:54 pm
  PM Quote Reply
8th Post
gmgiltd
Member
 

Joined: 07-10-2012
Location: Whitehills , United Kingdom
Posts: 142
Status: 
Offline
Hi Joachim ,
If you do go the Hispec route there are a couple of catchits. I took my car in there just over a year ago and provided them with a back axle and they measured up everything. Fronts are excellent but the rears took a bit of work with spacers and longer studs and getting the handbrake linkage right. Keep in mind that I am using 15" wheels from the club store so you will need to provide them with the accurate internal dimensions of whatever rims you intend to use. Speak to Alex - very helpfull there.
Gordon

Back To Top PM Quote Reply

 Posted: 03-01-2013 08:09 pm
  PM Quote Reply
9th Post
sholdowa
Member


Joined: 01-03-2012
Location: Diamond Harbour, New Zealand
Posts: 21
Status: 
Offline
Availability was zero down here so I'm having the mc rebuilt. $160 + tax for resleeving in stainless and a rebuild.

Back To Top PM Quote Reply  

Current time is 07:40 pm  
> Jensen Healey & Jensen GT Tech > Brakes > Metric? Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems