Home 
Home Search search Menu menu Not logged in - Login | Register
> Jensen Healey & Jensen GT Tech > Ignition > Crank Fire Ignition

 Moderated by: Greg Fletcher
New Topic Reply Printer Friendly
Crank Fire Ignition  Rating:  Rating
AuthorPost
 Posted: 12-22-2012 08:24 pm
  PM Quote Reply
1st Post
navy
Member
 

Joined: 12-13-2009
Location:  
Posts: 3
Status: 
Offline
I have just installed Steven DuChene, crank  fired ignition kit, on my 1974,

907 Jensen Healey.  Superior quality machined brackets, east to follow

instructions.

No more distributor leaks.  From average running to spot on timing, and

super acceleration.

This should be a  upgrade to all Jensen Healeys.

Navy  Las Cruces NM

 

Back To Top PM Quote Reply  

 Posted: 12-23-2012 05:50 am
  PM Quote Reply
2nd Post
Jensen Healey
Super Moderator


Joined: 03-11-2005
Location: San Anselmo, California USA
Posts: 976
Status: 
Offline
How much was it and how can we get them?

Kurt

Back To Top PM Quote Reply

 Posted: 12-23-2012 05:00 pm
  PM Quote Reply
3rd Post
navy
Member
 

Joined: 12-13-2009
Location:  
Posts: 3
Status: 
Offline
Kurt,

In this catagory, ignition, see progress on crank fired distributors installation

by Steven D57, dated 3/31/12.

He has a 14 page article for for the asking includes cost, etc.

Jim Navy--Las Cruces NM

Back To Top PM Quote Reply  

 Posted: 12-24-2012 08:08 pm
  PM Quote Reply
4th Post
Frank Schwartz
Member
 

Joined: 02-18-2011
Location:  
Posts: 244
Status: 
Offline
Merry Christmas to all and Happy New Year!

I have all the parts ready to install except the megajolt unit.  Where did you get it?  I seem to have trouble with the megajolt web site and how to contact those people.  How much was it?  Did you program it?  I am unable to accomplish and computer programming and Steve said he would do it for me when I get the megajolt.....

 

Frank Schwartz

Back To Top PM Quote Reply

 Posted: 12-24-2012 10:43 pm
  PM Quote Reply
5th Post
StevenD57
Member


Joined: 04-10-2009
Location: Hubbard, Ohio USA
Posts: 103
Status: 
Offline
I have an updated conversion article (version 4.01) as a 21 page PDF file . This article includes cost estimates for the various pieces necessary to do the conversion, wiring diagrams, parts lists, and a lot of background information on the why's and where-to-fore's behind the conversion.

Back To Top PM Quote Reply  

 Posted: 12-24-2012 10:49 pm
  PM Quote Reply
6th Post
StevenD57
Member


Joined: 04-10-2009
Location: Hubbard, Ohio USA
Posts: 103
Status: 
Offline
Frank Schwartz wrote: Merry Christmas to all and Happy New Year!

I have all the parts ready to install except the megajolt unit.  Where did you get it?  I seem to have trouble with the megajolt web site and how to contact those people.  How much was it?  Did you program it?  I am unable to accomplish and computer programming and Steve said he would do it for me when I get the megajolt.....

 

Frank Schwartz
Yes, I programmed Jim's Megajolt ECU for him and then sent it back to him. I believe he just purchased it through the Autosport Labs web site.

BTW, the new product name is the Megajolt/E (E for EDIS) since they are supposed to be coming out with a more complex follow-on product that will have a slightly different functionality and name. The Megajolt/E is still priced at $161.95 + $6.95 for the programming cable.

Back To Top PM Quote Reply

 Posted: 12-25-2012 02:42 am
  PM Quote Reply
7th Post
Frank Schwartz
Member
 

Joined: 02-18-2011
Location:  
Posts: 244
Status: 
Offline
OK...the next question is how do I find the company and how do I make a purchase from  them?   That has been my problem...

Frank

 

Oh, yes, again...Merry Christmas !!!!!!!!

Back To Top PM Quote Reply  

 Posted: 12-25-2012 04:06 am
  PM Quote Reply
8th Post
StevenD57
Member


Joined: 04-10-2009
Location: Hubbard, Ohio USA
Posts: 103
Status: 
Offline
Very simple. Go to:

http://www.autosportlabs.com/megajolte-p-41.html

then scroll down to the bottom third of the page, just past the pictures of the "System Diagram" and "Tuning Software" where you will see some pull down menus to make choices about the options you want to order. The three default choices are "No Hard Rev Limit needed", "Internal 2.5 Bar Manifold Pressure (MAP) Sensor", and "Include Cable (+6.95)". Leave those at the default and then just below that and over on the right there will be a small button that says "Add to Cart". Click that which will take you to the contents of your current shopping cart. You should end up with a total of $168.90 and another button on the right side that says "Checkout". Click that and then follow the directions for "I am a new customer" with a continue button. Fill out all of the stuff on the next page and then again click "Continue" which in theory should take you to the next page where you enter your payment information.

Back To Top PM Quote Reply

 Posted: 12-25-2012 05:36 am
  PM Quote Reply
9th Post
Frank Schwartz
Member
 

Joined: 02-18-2011
Location:  
Posts: 244
Status: 
Offline
Right !    I'll do it tomorrow...probably in the evening after I have stuffed myself on Turkey and all the trimmings...  

Thank you,

Frank

Back To Top PM Quote Reply  

 Posted: 12-25-2012 08:04 pm
  PM Quote Reply
10th Post
Frank Schwartz
Member
 

Joined: 02-18-2011
Location:  
Posts: 244
Status: 
Offline
I ordered it today !  My Christmas  present to me.  

Merry Christmas to all and to all a good night !!!!

Back To Top PM Quote Reply

 Posted: 12-27-2012 12:51 pm
  PM Quote Reply
11th Post
Jensen Healey
Super Moderator


Joined: 03-11-2005
Location: San Anselmo, California USA
Posts: 976
Status: 
Offline
StevenD57 wrote: I have an updated conversion article (version 4.01) as a 21 page PDF file . This article includes cost estimates for the various pieces necessary to do the conversion, wiring diagrams, parts lists, and a lot of background information on the why's and where-to-fore's behind the conversion.

Hi Steven, Please forward the PDF to:

klhoush at comcast.net 

Thanks and happy holidays,

Kurt

Back To Top PM Quote Reply  

 Posted: 01-01-2013 08:00 pm
  PM Quote Reply
12th Post
jdenglish
Member
 

Joined: 02-11-2009
Location:  
Posts: 78
Status: 
Offline
Hello Steve,
Could you include me in that e-mail.
Thanks,
John English
JH5 20175
jdenglish@comcast.net

Back To Top PM Quote Reply

 Posted: 01-10-2013 08:25 pm
  PM Quote Reply
13th Post
answerman
Member
 

Joined: 09-10-2012
Location: Little Chute, Wisconsin USA
Posts: 381
Status: 
Offline
Is this the same procedure that was in the most recent JHPS newsletter?

Back To Top PM Quote Reply  

 Posted: 01-15-2013 06:53 pm
  PM Quote Reply
14th Post
StevenD57
Member


Joined: 04-10-2009
Location: Hubbard, Ohio USA
Posts: 103
Status: 
Offline
Yes, The article in the JHPS bulletin is a reprint of my 21 page article. I believe Greg split it up into two parts since it was so long.
--
Steve

Back To Top PM Quote Reply

 Posted: 03-12-2013 03:54 pm
  PM Quote Reply
15th Post
jdenglish
Member
 

Joined: 02-11-2009
Location:  
Posts: 78
Status: 
Offline
Hi Steve,
I'm still lurking. I have your PDF version 3.96. could I get the 4.01 update? My last post was listed as 1-1-13 but it was probably back in March of 2012. Thanks again,
John

Back To Top PM Quote Reply  

Current time is 12:51 am  
> Jensen Healey & Jensen GT Tech > Ignition > Crank Fire Ignition Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems